Hello Good NightSorry i have a problem for my network, for you information my topologi network isSwitch Core (WS-C3850-24XS Staging) Switch Access 1 WS-C2960X-48TD-L Switch Access 2 WS-C2960X-48TD-LSwitch Access 3 WS-C2960X-48TD-LSwitch Access 4 WS-C...
Forum Posts
Dear all, I was enabling PoE on a 1921 router which has EHWIC-D-8ESG-P card. The running ios is "c1900-universalk9-mz.SPA.154-3.M5.bin". I neither see any power enable command in the global nor I see anything under the interface which could enable ...
Resolved! Cisco Catalyst 3560 not boot
Hi.I have a Cisco Switch 3560 and not boot. The Leds: SYST, RPS, STAT, Duplx, Speed, PoE (all Leds) are always green and the POST test not run. With a serial cable connect, don't output everything for putty.IOS: Version 12.2(35)SE5Model: WS-C3560-24P...
I am stumped.I have a native vlan mismatch on a trunked port channel between a C1300 and 2 nexus 9336c-fx2. Now I do have this configured as a vpc on the nexus side just fyihere are the details:C1300g17,18channel-group 1 mode autosw mode trunksw trun...
I mistakenly did the factory reset-all on my Cisco 9200 switch and now the switch is only showing the switch: prompt at start-up. How do I get the switch back to where it belongs with no config and booting from the packages.conf?
Hello: I saw that some people have this problem. I have no access to the console to my cisco 3560 switch. I can not access rommon mode too. I just have blank screen despite the fact that the serial configuration was done properly: Bits per second:960...
Greetings all, I have a Catalyst 9200 Switch. Would it be possible to immediately send to a Syslog server of MAC addresses of devices whenever they plug into any of the switch ports? I understand this is possible via SNMP traps but is it possible via...
Hello, I am working on setting up a relatively small but somewhat complex network using a 2960S-48 port switch connected to a 2921 ISR router then connected to an ASA. All data traffic will be routed through a VPN back to the main office and VOIP wi...
I have a home network setup. I am tearing down a lot of it as I don't use it. Parr of it is taking out the small rack my 48 port Cisco switch was in as I need the space. My question is, can I put my Cisco switch on a table top and let it sit there an...
Resolved! Ask a Question about switch design
Hi My Name Is Bobi 1.In the attached scenario where the servers are located?2.Which switches should vlan routing perform?3.What form and protocol should be used for routing?Thanks for taking the time to answer my questions
hello,I have a question about this log, why only few BPDU frames sent versus huge revived ??Wan-SW123 #sh spanning-tree interface tenGigabitEthernet 1/1/1 detailPort 29 (TenGigabitEthernet1/1/1) of VLAN322 is root forwarding Port path cost 2000, Po...
Hi allI have an SQL server that is due to move to a new pair of Nexus 9000 leaf switches, with a VPC configured between them. The ports on the new switches are configured as LACP active, just like the other SQL servers, and when this move was first a...
Hello everyone,I have an issue with STP for the topology above, I need to run STP so that one of the customer's links will be in STP Alt state.The configuration is as follows:Site1-Eth1/1 (Towards Customer CE):switchport mode dot1q-tunnelswitchport a...
Hi all,I have Cisco Nexus 9xxx switch and 100G SR4 QSFP AOC breakout module. I want to do BERT test at each of the 4 lanes so I want to tell the switch to set the QSFP in loopback mode (whatever comes in the RX goes out in TX) then I have 25G BERT wi...
So, we have a 3750. In the running config it doesn't show the "ip routing" command anywhere, but it does have have a routing table (mostly statics). Is routing only enabled with the "ip routing" command in the running config?
