We're having an issue with OSPF routing done on a Nexus9000 that we are not able to figure out. To explain the situation fully, I'm going to provide quite a bit of information, I apologize in advance. Our organization currently has several branches, ...
Hi,I built a small lab with 5 routers. On some routers I have distributed the loopback addresses on the network.R1:router bgp 100bgp log-neighbor-changesneighbor 10.1.1.2 remote-as 200neighbor 10.1.2.2 remote-as 300R1#show ip routeB 4.4.4.4 [20/0] vi...
Hello expertsI have a problem with an MPLS adjacency.I have an ASR900 connected to a 10Gb C9300, MPLS and OSPF are enabled in this interface, adjacencies are created and everything works.When the C9300 is restarted, the MPLS and OSPF adjacencies are ...
I need same help for understanding... The configuration: RT1 and RT2 are layer 3 switchesFW is a Layer3 Firewall RT1 holds networks (Range-1) of the range 10.0.0.0/17 and the connection to internet (default way)RT2 holds networks (Range-2) of the ran...
¡Saludos a todos!Tengo la siguiente topología:(Proveedor)<----- BGP ------->(Nexus 9396)<----- OSPF ----->(Router downstream)Quiero redistribuir la ruta por defecto aprendida por BGP al router downstream vía OSPF, pero este router no lo termina de ap...
Looking for recommendations for routing traffic from ASA back to router on "inside" network so we do not have to add static routes on systems. We recently added an ASR1001 to our "inside" network that routes traffic to Amazon thru a Megaport link tha...
I'm confused about something and I'd like your help in understanding. Where I work, we have a router that's connected to 2 ISPs via BGP. Weight is set to 100 to ISP-A and 50 to ISP-B so outbound traffic is going through ISP-A and AS-Path prepend is m...
hi, We are trying upgrade IOS for a ISR4321 from 16.3.8 to 17.6.6..currently on 16.3.8 the rommon version is 16.9(1r).as part of the ios upgrade we tried to upgrade the rommon to 16.12(2r) but we get the below error when doing so.FAILURE: MD5 signatu...
Hi all, my edge routers are running IOS-XR 7.7.21. We have quite a bit of intentionally exposed customer public address space and have endless problems with garbage traffic from a select few ASN's who don't police their networks (14061 Digital Ocean...
Good afternoon:Run a simulation in packet tracer to implement a router on stick with two vlans. The simulation worked without problems, and I want to implement the same on my cisco 867VAE router.This equipment has a Giga interface for WAN (Ge1), and ...
Hi,I have a router with two WAN interfaces towards to different ISPs. Each ISP is in active/stand-by using floating default routes so, there is only one active default route in the routing table. For the nat I have two NAT overload statements using t...
My question, I have a Cisco router C4221. From Cisco document, C4221 have aggregation throughput for un-subscription is 35Mbps. But after I do monitor on Zabbix, I found that the overall | aggregation throughput reach over to 55Mbps. Moreover, the co...
Hi all,I'm having an issue setting up an L2TPv3 tunnel between two routers. The routers are both 4431-SEC/K9's running 17.9.4a and have AppX licences loaded and in use:ISR_4400_Application (ISR_4400_Application):Description: AppX License for Cisco IS...
Dear Gents, I have cisco switch C9200L with DNA-Essentials, I want to connect two different servers to same switch and i want to track each port connected to each server like if server-1 down then the other port connected to server-2 will be on Th...
We have two switches. Next to them is the switch with the IP camera. The NVR is in another building. Will there be traffic load on the main uplink? The network will be slow. If we only put the NVR online and provide its display in another building, w...
